Last Updated on
Most of the chainsaw users often face a common issue while starting their chainsaw. Their chainsaw won’t start has spark and fuel though. Has your chainsaw ever dragged you into such situation? Well, there are several possible reasons behind such situation no matter how much effort you're giving.
Whether it's a old or new chainsaw for private or regular using, this occurrence might happen to anyone. We’re here with some of the basic causes behind the starting issues of a chainsaw and some tips to get over those problems. It’s always better to know the reasons so that you can overcome the problems you’re having. Shall we begin?
Why Doesn’t Your Chainsaw Start Even if It has Spark and Fuel?
Check out the technical errors and damages why your chainsaw won't start with starting fluid and spark. Know the issues and eliminate them from their roots.
The rewind spring, the recoil starter pulley, and the magneto assembly consist of electromagnet windings and a magnet, are the three main parts of the recoil starter. If either of these parts is broken or worn-out somehow, your chainsaw won't start so the chainsaw needs maintenance. Check them and replace them as required.
The Ignition Coil
One of the greatest precious parts of the chainsaw to make it start is the ignition coil. If it's broken or damaged somehow, even your new chainsaw won’t start. It converts the low voltage into high voltage to perform the electric spark. Use an ignition coil tester or a multimeter and check if there's an error. If so, replacing the coil is the only solution.
A Flooded Engine
Excessive pushing of the fuel pump or primer bulb can cause a flooded engine. When you can smell the fuel while starting the saw or feel too much moisture around the spark plug, that indicates to a flooded engine and it’s time for some fuel draining.
Following blades can draw the highest performance, have a try..
Check the compression rings if they're exhausting bluish gases. It means they are worn out. Or you can also check the spark plug how often it gets sooty deposits. That indicates to the piston rings leakage. If either of the issues occurs, it's time for changing the compression rings. Otherwise, they won't be able to produce enough heat for sparking.
It's normal that after using a limited amount of time, the fuel filter of your chainsaw will get clogged. It traps dirt because of the oil. Such clogging blocks the fuel to pass in a required amount. So, keep changing and cleaning the fuel filter regularly after using it several times.
Dirty Air Filters
Dirty and clogged air filters also prevent the saw from getting a start. Remove and clean the air filter after 5 hours of usage.
Gear assembly doesn't get enough power transferred from the crankshaft’s flywheel because of the broken clutch pads. Because broken clutch pads can't attach that flywheel properly. It prevents starting the saw. To avoid this, you have to replace the whole set of clutch plate.
A clogged carburetor can cause your chainsaw not getting started. Fuel evaporation is the main reason for such clogging. You have to clean the fuel tank and also the carburetor regularly to prevent unwanted clogging.
The spark arrestor prevents setting on fire in the dry season because of the exhausting particles from a spark. But it gets clogged with time and causes unintentional blocking to burn the fresh fuel-air mixture well. So, to avoid this situation, it requires replacement after every 24 hours of usage.
How to Maintain a Chainsaw for having Continuous Easy Starts?
Well, in the above section you’ve got to know the issue while staring a chainsaw and their remedies. Now, let us help you with some tricky tips for maintaining and getting your chainsaw started any time regardless its age.
- Never use it for over forty hours without a servicing. You should maintain servicing the chainsaw every time after using it for 25 hours.
- Try to use or at least run your chainsaw on a regular basis just to keep all its parts active.
- The more you use a chainsaw, the quality of the fuel gets worse with time. For a fast and easy start of the chainsaw, try to use fresh fuel.
- If you ever notice or have a doubt that one or some of the parts are not working properly, check it soon and replace it as soon as possible without wasting a single moment.
- Whenever you’re replacing or changing any part of your chainsaw, make sure it’s an original spare part. Otherwise, it will wear out sooner and also make other parts weak and disable.
- Avoid dump places to store the chainsaw. Make sure it’s a dry and clean place where you’re storing it to avoid damages.
Words To Wise
It’s not enough to know how to use a chainsaw or how to start a stubborn chainsaw. It doesn’t matter if it’s a chainsaw or any other power tool, the thing that matters the most is its maintenance. Such power tools come with so many moving and fragile parts. They require high maintenance. Take good care of your chainsaw, and it’ll do its best for you.
Austin R Dean
As a carpenter, I have been working for a long day with a different type of saw. What experience I have gathered, I intend to share that expertness to all. I will try to give several shorts of saw's reviews and important tricks. Thanks for coming here....