9 Best Miter Saw Blades for Aluminum (October 2026)
The best miter saw blades for aluminum include the TOMAX 10-Inch 80 Tooth TCG Aluminum for 10-inch miter saws, the TOMAX 12-Inch 100 Tooth TCG Aluminum for 12-inch saws, and the DEWALT Miter Saw Blade for a fine-finish general blade.
On this page (6 sections)
The best miter saw blade for aluminum is one specified for aluminum and approved for your saw, with a matching diameter, arbor and speed limit. The TOMAX 10-inch 80-tooth blade is the clearest fit here because it is designed for aluminum and its compatible devices include miter saws.
A blade that fits the arbor may still be unsuitable for the saw. A compatible miter saw fence system can help support stock while you work.
Check the saw manual for approved blade type and maximum speed, and secure aluminum stock as the manufacturer directs.
For blade installation guidance, see this video on tightening a Milwaukee miter saw blade.
Our picks at a glance
-
1
-
2
-
3
- 4
Check itRevvstark Circular Saw Blade 12 Inch 100T
Best for a 12-inch general-purpose option - 5
Check itTOYAKI 10-Inch Miter Saw Blade
Best for a fine-tooth aluminum cut - 6
Check itMASTEC 10-Inch 100T Carbide Tooth TCG
Best for a 10-inch 100-tooth blade - 7
Check itDiablo Saw Blade for Thick Aluminum
Best for portable saws and thick stock - 8
Check itEvolution 14BLADEAL14" 80T Aluminum Blade TCT Saw
Best for compatible low-RPM saws - 9
Check itIVY Classic 35056 Swift Cut 10"
Best for light-gauge aluminum
How we chose these miter saw blades for aluminum
We compared each blade’s stated material use, tooth design, dimensions and saw compatibility. A blade expressly described for aluminum and miter saw use ranks ahead of one whose miter-saw fit needs confirmation.
The TCG grind appears on several picks. Its alternating flat and chamfered tooth shape is commonly used for non-ferrous materials, but blade suitability still depends on the saw and stock.
We did not infer compatibility from diameter alone.
Compare aluminum blades by diameter and fit
Choose a blade only when its diameter, arbor, speed rating and intended saw type match your saw’s manual. The table highlights the details that matter most for these picks.
| Product | Best for | Diameter | Teeth | Arbor | Our score |
|---|---|---|---|---|---|
| TOMAX 10-Inch 80 Tooth TCG Aluminum | 10-inch miter saws | 10 in | 80, TCG | 5/8 in | 9.7 |
| TOMAX 12-Inch 100 Tooth TCG Aluminum | 12-inch saws | 12 in | 100, TCG | 1 in | 9.6 |
| DEWALT Miter Saw Blade | a fine-finish general blade | 12 in | 100 | 9.5 | |
| Revvstark Circular Saw Blade 12 Inch 100T | a 12-inch general-purpose option | 12 in | 100 | 1 in | 9.4 |
| TOYAKI 10-Inch Miter Saw Blade | a fine-tooth aluminum cut | 10 in | 120 | 5/8 in | 9.3 |
| MASTEC 10-Inch 100T Carbide Tooth TCG | a 10-inch 100-tooth blade | 10 in | 100, TCG | 5/8 in | 9.2 |
| Diablo Saw Blade for Thick Aluminum | portable saws and thick stock | 7-1/4 in | 56, TCG | 5/8 in | 8.6 |
| Evolution 14BLADEAL14" 80T Aluminum Blade TCT Saw | compatible low-RPM saws | 14 in | 80 | 8.3 | |
| IVY Classic 35056 Swift Cut 10" | light-gauge aluminum | 10 in | 200 | 5/8 in | 8.1 |
The best miter saw blades for aluminum
The TOMAX 10-inch blade is the strongest documented fit for a compatible miter saw, while the other options serve specific diameters, tooth counts or material limits. Check each blade’s stated use before you mount it.
TOMAX 10-Inch 80 Tooth TCG Aluminum: Best for 10-inch miter saws
- 10-inch diameter
- 80 carbide teeth
- TCG grind
- 5/8-inch arbor
This 10-inch blade has 80 carbide teeth and a TCG grind, and is specified for aluminum, plastic and non-ferrous metals. Its compatible devices include miter saws.
Pros
- Miter saw compatibility is specified
- TCG tooth grind
- Made for aluminum and non-ferrous metals
Cons
- Confirm the arbor and saw speed before buying
The TOMAX 10-inch blade is the most direct match for a 10-inch miter saw approved for aluminum cutting. It has 80 carbide teeth with a TCG grind, and TOMAX identifies miter saws among its compatible devices.
TOMAX also describes the blade for plastic and non-ferrous metals. Its coating is intended to reduce rust and corrosion, and TOMAX offers a limited lifetime warranty.
The 5/8-inch arbor must match your saw’s arbor or an approved adapter specified by the saw maker. Confirm the manual permits this blade type and that the saw’s speed does not exceed the blade’s limit.
Choose it when your saw accepts a 10-inch, 5/8-inch-arbor blade and its manual permits aluminum cutting. The stated miter-saw compatibility makes this a practical first option to compare.
TOMAX 12-Inch 100 Tooth TCG Aluminum: Best for 12-inch saws
- 12-inch diameter
- 100 carbide teeth
- TCG grind
- 1-inch arbor
The 12-inch TOMAX has 100 carbide teeth and a TCG grind for aluminum and other non-ferrous metals. Check that your miter saw accepts its 1-inch arbor.
Pros
- Designed for aluminum and non-ferrous metals
- 100-tooth TCG grind
- 12-inch diameter
Cons
- Arbor fit needs confirmation
The 12-inch TOMAX is the larger counterpart for saws designed around a 12-inch blade. It has 100 carbide teeth and a TCG grind, with aluminum, plastic and non-ferrous metal among its intended materials.
Its 1-inch arbor is a key fit detail. Do not assume a 12-inch saw accepts that arbor; check the manual and use only an approved setup.
TOMAX describes the TCG grind as suited to durable, smooth cuts in non-ferrous metals and plastic. The brand also says its electrophoretic coating reduces rusting and corrosion and offers a limited lifetime warranty.
This is the TOMAX choice to consider when your saw’s manual permits a 12-inch aluminum blade and confirms the 1-inch arbor. If your saw has a different arbor, choose a blade built for that fit instead.
DEWALT Miter Saw Blade: Best for a fine-finish general blade
- 12-inch diameter
- 100 teeth
- Ultra-sharp carbide
- Low-vibration body slot design
DEWALT describes this as a fine-finish miter saw blade with 100 teeth and ultra-sharp carbide. Its compatible materials include metal and wood, but aluminum is not specified, so confirm its intended use with DEWALT.
Pros
- Made for miter saws
- 100 teeth
- DEWALT describes it as a fine-finish blade
Cons
- Aluminum suitability needs confirmation
The DEWALT DWA112100 is a 12-inch, 100-tooth miter saw blade described for fine finishing. Its compatible materials include metal and wood, but aluminum is not specifically identified.
DEWALT highlights ultra-sharp carbide teeth, optimized tooth geometry and a body-slot design intended to reduce vibration. Those features do not confirm that the blade is suitable for your aluminum stock or saw setup.
Treat it as a candidate only if DEWALT and your saw manual confirm aluminum use. If you want a blade explicitly described for aluminum, compare the TOMAX or MASTEC options first.
Revvstark Circular Saw Blade 12 Inch 100T: Best for a 12-inch general-purpose option
- 12-inch diameter
- 100 carbide teeth
- 1-inch arbor
- Aluminum use is described
Revvstark describes this 12-inch, 100-tooth blade for cutting aluminum and non-ferrous metals. Its compatible devices are circular saws, so confirm miter saw use before choosing it.
Pros
- Aluminum use is described
- 100 carbide teeth
- 1-inch arbor
Cons
- Miter saw compatibility needs confirmation
Revvstark describes this 12-inch, 100-tooth blade for aluminum and non-ferrous metals, with a 1-inch arbor. Its compatible devices are circular saws, so miter-saw compatibility needs confirmation.
Its stated features include carbide teeth and noise-reducing perforations. Before using it on a miter saw, confirm the saw maker permits that blade type, diameter, arbor and operating speed.
This option may suit a buyer comparing aluminum blades for another compatible circular saw. For a miter saw, get confirmation from both the saw and blade makers before fitting it.
TOYAKI 10-Inch Miter Saw Blade: Best for a fine-tooth aluminum cut
- 10-inch diameter
- 120 carbide teeth
- 5/8-inch arbor
TOYAKI describes this 10-inch, 120-tooth blade for aluminum, plastic and non-ferrous metals. Its fine tooth count suits buyers comparing aluminum blades for a fine finish.
Pros
- Aluminum use is specified
- 120 teeth
- 5/8-inch arbor
Cons
- Confirm compatibility with your exact saw
The TOYAKI 10-inch blade is described for aluminum, plastic and non-ferrous metals. It has 120 teeth, a fine tooth count for buyers prioritizing a clean edge.
TOYAKI gives a 5/8-inch arbor and describes the blade as intended for miter saws, table saws and circular saws. Check your saw’s manual, speed limit and material guidance before cutting.
TOYAKI lists a 2.8 mm blade thickness. That detail helps you compare it with your saw’s blade requirements, but it does not replace a fit check.
Choose it if your approved 10-inch saw accepts the 5/8-inch arbor and its manual permits aluminum cutting. Its 120 teeth make it the highest tooth-count 10-inch option in this group.
MASTEC 10-Inch 100T Carbide Tooth TCG: Best for a 10-inch 100-tooth blade
- 10-inch diameter
- 100 carbide teeth
- TCG grind
- 5/8-inch arbor
MASTEC specifies this 10-inch blade for miter saws, circular saws and table saws. Its TCG teeth are intended for aluminum, plastic and non-ferrous metals.
Pros
- Miter saw use is specified
- TCG tooth geometry
- 5/8-inch arbor
Cons
- Confirm your saw’s maximum speed and blade requirements
MASTEC specifies this 10-inch, 100-tooth TCG blade for aluminum, plexiglass, plastic and non-ferrous metals. The brand names miter saws, circular saws and table saws as compatible machines.
Its 5/8-inch arbor is a fit detail, but your saw’s manual remains the authority. MASTEC’s product description gives a maximum operating speed of 5,000 RPM, so make sure the saw does not exceed that limit.
The blade has carbide teeth and a 2.8 mm thickness. Its TCG design makes it a direct aluminum-cutting candidate when diameter, arbor, speed and saw approval all match.
Choose MASTEC if you want a 10-inch, 100-tooth TCG option with miter saw use specified. Check the manual for the material, workholding and blade rules before cutting.
Diablo Saw Blade for Thick Aluminum: Best for portable saws and thick stock
- 7-1/4-inch diameter
- 56 TCG teeth
- 5/8-inch arbor
- Designed for thick aluminum
Diablo describes this 7-1/4-inch TCG blade for thick aluminum and other non-ferrous materials. It is specified for circular saws, so check with Diablo and your saw maker before using it on a miter saw.
Pros
- Designed for thick aluminum
- TCG tooth geometry
- 5/8-inch arbor
Cons
- Miter saw compatibility is not specified
Diablo’s blade is designed for thick aluminum and other non-ferrous materials, including copper, brass, plastics and fiberglass. It is a 7-1/4-inch blade with 56 TCG teeth, so it will not fit a 10-inch or 12-inch miter saw.
The compatible device is a circular saw. Its 5/8-inch arbor does not mean it is approved for a miter saw.
Diablo describes a non-stick coating and stabilizer vents intended to manage gumming, heat and vibration. For a miter saw, use this blade only if the saw maker explicitly approves the size, type and application.
This pick belongs on the shortlist for a compatible portable circular saw and thick aluminum stock. Miter saw users should choose a blade expressly approved for their specific machine.
Evolution 14BLADEAL14" 80T Aluminum Blade TCT Saw: Best for compatible low-RPM saws
- 14-inch diameter
- 80 carbide teeth
- 1-inch arbor
- Maximum 1,600 RPM
Evolution designed this 14-inch aluminum blade for its named saws and other low-RPM saws. Its 1,600 RPM maximum makes speed compatibility a key check.
Pros
- Designed for aluminum
- Maximum speed is specified
- Compatible saw models are named
Cons
- Not a general fit for standard-speed miter saws
The Evolution 14BLADEAL is a specialized 14-inch aluminum blade for Evolution models and other low-RPM saws. Its stated maximum speed is 1,600 RPM, so check that the saw does not exceed this limit.
Evolution names several compatible models, including the S355CPSL, S380CPS and EVOSAW380. The product data also names select saws from other brands, but check your exact model and manual before buying.
The blade has 80 carbide teeth and a 1-inch arbor. Evolution describes its dry-cut technology as cutting with very little heat and few burrs, while setup and workholding should follow the saw instructions.
Consider it only when your saw appears in the named compatible models or its maker confirms the fit and speed. It is not a general-purpose blade for ordinary high-speed miter saws.
IVY Classic 35056 Swift Cut 10": Best for light-gauge aluminum
- 10-inch diameter
- 200 teeth
- 5/8-inch arbor
- For aluminum up to 1/8 inch thick
IVY Classic specifies this steel blade for light-gauge aluminum up to 1/8 inch thick, plus plastic and vinyl siding. It is specified for circular saws, so verify miter saw use before fitting it.
Pros
- Thickness limit is clear
- 200 precision-ground teeth
- 5/8-inch arbor
Cons
- For light-gauge stock only
- Miter saw compatibility needs confirmation
IVY Classic specifies this 10-inch, 200-tooth steel blade for light-gauge aluminum up to 1/8 inch thick, along with plastic and vinyl siding. For thicker aluminum, IVY Classic points to a different blade.
It has a 5/8-inch arbor and precision-ground teeth. The compatible device is a circular saw, so confirm miter-saw use with IVY Classic and your saw manual before considering it.
The thickness limit matters more than the high tooth count. Do not use it for stock above the stated limit or assume that it suits other aluminum-cutting jobs.
This is a narrow choice for light-gauge material when the saw makers approve the setup. For thicker stock, use a blade specifically intended for that material and approved for your saw.
What should you check before fitting an aluminum blade?
Check the blade diameter, arbor size, maximum speed and approved material in your miter saw manual before buying. Each requirement must match, and a blade’s fit on the arbor alone does not mean it is safe or approved.
Miter saws are built for specific blades and applications. Read Can You Use A Metal Blade On A Miter Saw? for compatibility checks that apply to metal cutting.
Also confirm that the blade’s rotation arrow faces the correct direction. Clamp and support the aluminum as your saw’s manual instructs, keep hands away from the cutting path, and wear eye and hearing protection.
Which tooth grind and tooth count suit aluminum?
A TCG blade is a sensible starting point for aluminum because several blades here are specifically described for non-ferrous cutting with that grind. Tooth count is one selection detail, so balance it with the stock, saw guidance and cut you need.
The 80-tooth TOMAX and 100-tooth MASTEC are both TCG options for 10-inch saws. The 120-tooth TOYAKI offers a higher tooth count, while the 200-tooth IVY Classic is limited to light-gauge aluminum up to 1/8 inch.
For a broader look at metal-cutting options, see our best 10 inch miter saw blade for metal guide. To compare other blade uses, start with Best Miter Saw Blade and Which Miter Saw Blade To Use?.
How do you choose the right aluminum blade for your saw?
Choose a blade whose stated material use and saw compatibility match your manual, then verify diameter, arbor and maximum speed. The TOMAX 10-inch is the clearest miter-saw match here; choose the 12-inch TOMAX for a compatible 12-inch saw, or the MASTEC for a 10-inch TCG option.
If compatibility is unclear, ask the saw or blade maker before cutting. Never rely on diameter or arbor fit alone when choosing a miter saw blade for aluminum.
Our top 3 picks at a glance
-
1
-
2
-
3
