9 Best Router Bit Sets (November 2026)
The best router bit sets include the Hiltex Router Bit Set for most woodworkers, the KOWOOD Router Bits Set of 15 Pieces for beginners, and the BOSCH RBS015MBS 15-Piece Carbide-Tipped Wood Router Bits for named profiles.
On this page (10 sections)
- How we compared these router bit sets
- The best router bit sets in detail
- How do 1/4 inch and 1/2 inch router bit sets compare?
- What profiles should a general purpose router bit set include?
- Which router bit set is best for your router brand?
- How many pieces should you buy in a router bit set?
- What carbide and storage should you look for?
- Can a router bit set handle router table work?
- What is the verdict on the best router bit set?
- How we compare router bit sets: specs, profiles and fit
The best router bit set for most woodworkers is the Hiltex Router Bit Set, because its 15 pieces cover the profiles you will reach for first.
It gives you straight bits in four sizes, core box and cove bits, a 90 degree V-groove, a mortising bit, a roundover, a dovetail, a Roman ogee, a 45 degree chamfer, a panel pilot and a flush trim bit.
Our picks at a glance
-
1
-
2
-
3
Best for named profilesBOSCH RBS015MBS 15-Piece Carbide-Tipped Wood Router Bits
9.5/10 our score
See it on Amazon
- 4
Check itLU&MN Carbide Tipped Router Bit Set
Best for largest variety - 5
Check itMNA Router Bit Set 25 Pieces 1/4
Best for 25 piece value - 6
Best for mixed shank workCheck it - 7
Check itMNA Router Bits Set 15 Pieces 1/4
Best for DIY woodworkers - 8
Check itWhiteside 401 Basic 7 Piece Router Bit
Best for 1/2 inch basics - 9
Check itWhiteside 404 Compact Router Bit Set
Best for compact routers
How we compared these router bit sets
We compared specs, features and buyer feedback for each set, including shank size, piece count, carbide type, case style and named profiles.
We did not test them hands on.
If you are new to routers, start with our guide to wood routers for woodworking so the router and the bits match. Then use how to set a router bit before your first cut.
The best router bit sets in detail
The picks below are ordered by score, from the Hiltex at 9.7 down to the Whiteside 404 at 8.1.
Each write up explains who the set suits, what its specs mean in daily use and where it sits against the others.
Hiltex Router Bit Set: Best for most woodworkers
- 15 pieces, 1/4 inch shank
- YG8 tungsten carbide tips
- Hardened alloy steel body
- Labeled hard storage case
A 15-piece 1/4 inch set that covers straight, cove, core box, V-groove, mortising, roundover, dovetail, Roman ogee, chamfer, panel pilot and flush trim work.
Pros
- Broad profile coverage in 15 pieces
- 1/4 inch shank fits most routers
- Labeled case keeps bits organized
Cons
- 1/4 inch shank only
- Packaging may vary between two styles
Hiltex suits a woodworker who wants one case for edging, trimming, veining, grooving and joinery. For steadier straight cuts along an edge, see router edge guides for woodworking.
The 15 pieces include four straight bits, two core box bits and one cove bit, plus a 90 degree V-groove, mortising, roundover, dovetail, Roman ogee, 45 degree chamfer, panel pilot and flush trim bit.
Its YG8 tungsten carbide tips cut cleanly in all types of wood. The hardened alloy steel body has a powder coated finish.
The 1/4 inch shank fits any router with a 1/4 inch collet, from trim routers to full size plunge and fixed base routers. Select bits have a ball bearing guide for smooth edge routing.
The trade off is shank choice, since there are no 1/2 inch bits for larger work. If your router has a 1/2 inch collet, see our router collet adapter guide.
The labeled hard case helps you find the right profile fast, and packaging may vary between two styles.
KOWOOD Router Bits Set of 15 Pieces: Best for beginners
- 15 pieces, 1/4 inch shank
- Hardened steel body
- Wooden storage case
- For wood, MDF, particle board and plywood
A beginner focused 15-piece 1/4 inch set in a wooden case for household and craft woodwork.
Pros
- Wooden case for storage
- 1/4 inch shank for stability
- Works with common wood materials
Cons
- Do not cut ferrous metal or non wood materials
- Profile list is less detailed than some sets
KOWOOD suits beginners who want a simple 15 piece set in a wooden case.
The 1/4 inch shank bits give more stability and less vibration than thinner shanks, and they fit most handheld or table routers.
KOWOOD says the hardened steel body and balanced build handle heavy duty use, and the design is meant to cut sticking and kickback risk during installation and use.
The set works with wood, MDF, particle board, plywood and compact panel.
It should not cut ferrous metal or non wood materials such as steel, iron or sand.
The wooden case makes storage and travel easier between jobs.
Compared with Hiltex, KOWOOD gives less detail on exact profiles, so you get a clear beginner set but less certainty about each size.
If you want a first set for household and craft woodwork, this is a practical pick.
If you plan router table joinery right away, a set with named sizes may serve you better.
BOSCH RBS015MBS 15-Piece Carbide-Tipped Wood Router Bits: Best for named profiles
- 15 pieces, carbide tipped
- Micrograin carbide tips
- Anti-friction coating
- Plastic storage case
A 15-piece BOSCH set with exact named profiles including chamfer, dovetail, V-groove, slotting, rabbeting, flush trim, Roman ogee, cove, roundover and straight bits.
Pros
- Exact profile sizes stated
- Micrograin carbide tips
- Plastic case for carrying
Cons
- Shank size is not stated in the data here
- 15 pieces limit spare duplicates
BOSCH RBS015MBS suits buyers who like exact named profiles.
The 15 bits include two chamfer bits, a 12 degree x 9/16 inch dovetail bit, a 60 degree x 5/8 inch V-groove bit, a 5/32 inch two wing slotting cutter, a 1/4 x 1/2 inch rabbeting bit, a 1/2 x 1 inch top bearing straight trim bit, a 5/8 x 1 inch double flute flush laminate trim bit, a 5/32 x 1/2 inch Roman ogee bit, a 3/8 x 1/2 inch cove bit, roundover bits in 1/4 x 1/2 inch and 1/8 x 3/8 inch, and double flute straight bits in three sizes.
BOSCH says micrograin carbide tips give smooth finish cuts and wear resistance, and the anti friction coating helps limit residue build up.
It is made for soft and hard wood and wood composites, and the plastic storage case helps you carry the set. Shank size is not stated here, so confirm fit with your collet.
For flush trimming and clean edges on a router table, these named sizes make planning easier.
LU&MN Carbide Tipped Router Bit Set: Best for largest variety
- 35 pieces, 1/4 inch shank
- Tungsten carbide tips
- Aluminum box packing
- Straight, flush trim, cove, dovetail and more
A 35-piece 1/4 inch set with the widest profile list here, from straight and flush trim bits to beading, wave edge and double Roman ogee bits.
Pros
- 35 profiles in one set
- Aluminum box for storage
- 1/4 inch shank fits most routers
Cons
- Large set takes more bench space
- More bits to track and clean
LU&MN suits a shop that wants the largest variety in one box.
The set has 35 pieces with a 1/4 inch shank, and the list runs from six straight bits and four flush trim bits to cove box, Roman ogee, cove, wave edge, dovetail, mortising, round nose, V-groove, panel pilot, rounding over, slot cutter, beading, classical cove and double Roman ogee bits.
Tungsten carbide tips are made to cut cleanly in all types of wood and to limit splintering.
The aluminum box packing helps with storage and carrying.
That 35 piece count means you can handle edging, trimming, veining and grooving without buying add on profiles right away.
The trade off is bulk, since 35 bits take more space and time to clean and sort than a 15 piece set, and several sizes overlap.
If you run a router table or make varied projects, the choice can save repeat purchases.
If you only need basics, a smaller set keeps your bench simpler.
MNA Router Bit Set 25 Pieces 1/4: Best for 25 piece value
- 25 pieces, 1/4 inch shank
- C3 carbide
- Protective storage case
- For MDF, hardwood, softwood and particle board
A 25-piece 1/4 inch all-purpose set with mortising, bevel, cove, core box, straight, panel pilot, flush trim, chamfer, dovetail, roundover, V-groove and Roman ogee bits.
Pros
- 25 pieces for general work
- C3 carbide for wear resistance
- Fits handheld and table routers
Cons
- Exact sizes per bit are not listed
- Case style differs from wooden cases
MNA 25 piece set suits a professional woodworker who wants a broad all purpose kit.
It includes mortising, combination bevel, cove, cove box, straight, panel pilot, bearing flush trim, chamfer, dovetail, roundover, V-groove and Roman ogee bits in a protective storage case.
The bits use American industry classification C3 carbide for wear resistance and sharp edges.
The universal 1/4 inch shank fits handheld and benchtop router table use with brands such as Bosch, DeWalt, Makita, Milwaukee, Porter and Cable, Skil, Ryobi and Black and Decker.
It fits MDF, hardwood, softwood and particle board.
Compared with the 15 piece sets, this 25 piece count adds choice without jumping to 35 pieces.
The trade off is that exact sizes for each bit are not listed, so you cannot plan a precise groove or profile from the data here.
For general shop work where you need most popular profiles, that is a fair trade.
For fine joinery with tight size needs, named sizes help more.
BOSCH Router Bits: Best for mixed shank work
- 10-piece all-purpose set
- 1/4 inch and 1/2 inch shank bits
- Micrograin carbide tips
- Storage case with wood base and clear top
A 10-piece BOSCH all-purpose set that mixes 1/4 inch and 1/2 inch shank bits for straight, surface forming, joinery, edge forming and trimming work.
Pros
- Mix of 1/4 and 1/2 inch shanks
- Named bit numbers included
- Clear top case shows bits
Cons
- Only 10 pieces
- Mixed shanks need two collets
BOSCH Router Bits suits a woodworker whose router accepts both 1/4 inch and 1/2 inch collets.
This 10 piece all purpose set mixes shanks, with straight and mortising bits 85460M, 85265M and 85249M, surface forming bits 85444M and 85219M, cabinetry and joinery bit 84709M, edge forming bits 85594M, 85592M and 85597M, and trimming bit 85441M.
Micrograin carbide tips are precision ground for sharper edges and a smoother finish.
The 1/2 inch shank bits give more stability and less vibration, while the 1/4 inch shank bits suit thinner profiles.
The storage case has a solid wood base and a clear plastic top, so you can see the bits without opening it.
The trade off is count, since 10 pieces cover fewer sizes than 15 or 25 piece sets.
Mixed shanks also mean you need the right collet for each bit.
If cross compatibility matters more than sheer count, this mix is useful.
If you own only one collet size, a single shank set is simpler.
MNA Router Bits Set 15 Pieces 1/4: Best for DIY woodworkers
- 15 pieces, 1/4 inch shank
- Carbide tips
- Classical wood case
- For MDF, hardwood, softwood and particle board
A 15-piece 1/4 inch DIY set in a classical wood case with mortising, cove, core box, straight, panel pilot, flush trim, chamfer, Roman ogee, dovetail, roundover and V-groove bits.
Pros
- Wood case for bench storage
- Common profiles for DIY work
- 1/4 inch shank fits most routers
Cons
- Exact sizes per bit are not listed
- 15 pieces only
MNA 15 piece set suits DIY woodworkers who want common profiles in a classical wood case.
The set includes mortising, cove, cove box, straight, panel pilot, bearing flush trim, chamfer, Roman ogee, dovetail, roundover and V-groove bits.
The bits are made to American dimensions and use MNA carbide for wear resistance and sharp edges.
The universal 1/4 inch shank fits handheld and benchtop router table use with brands such as Bosch, DeWalt, Makita, Milwaukee, Porter and Cable, Skil, Ryobi and Black and Decker.
It fits MDF, hardwood, softwood and particle board.
Compared with the MNA 25 piece set, this set is smaller and easier to store, but gives fewer sizes for duplicate profiles.
Compared with Hiltex, it gives less detail on exact bit sizes.
That makes it a good pick for general DIY work, less good for a project that needs a precise named size.
Whiteside 401 Basic 7 Piece Router Bit: Best for 1/2 inch basics
- 7 pieces, 1/2 inch shank
- Cove, rabbet, roundover, chamfer, straight and flush trim
- Hardened plastic case
- For natural wood, composite wood and hard plastics
A 7-piece 1/2 inch shank basic set with a 3/8 inch radius cove, 3/8 x 1/2 inch rabbet, 3/8 inch roundover, 45 degree chamfer, 1/4 inch straight, 1/2 inch straight and 1/2 inch flush trim bit.
Pros
- 1/2 inch shank for stability
- Exact bits named by number
- Compact plastic case
Cons
- Only 7 pieces
- 1/2 inch collet required
Whiteside 401 suits a router owner with a 1/2 inch collet who wants seven core bits.
The set includes R3/8 inch cove bit 1804, 3/8 x 1/2 inch rabbet bit 1901, R3/8 inch roundover bit 2008, 45 degree chamfer bit 2305, 1/4 inch straight bit 1058, 1/2 inch straight bit 1067 and 1/2 inch flush trim bit 2405.
The 1/2 inch shank gives more stability and less vibration for heavier cuts.
It is stated for natural woods, composite woods and hard plastics, with clean and precise cuts across those surfaces.
The hardened plastic case helps with organization and transport.
The trade off is scope, since seven bits cannot cover dovetail, V-groove, Roman ogee or mortising work.
It also needs a 1/2 inch collet, so it will not fit a trim router limited to 1/4 inch.
For basic edge shaping, rabbeting and flush trimming, the exact bit numbers make it easy to map to a project.
Whiteside 404 Compact Router Bit Set: Best for compact routers
- 4 pieces, 1/4 inch shank
- Flush trim, 1/8 inch roundover, template and 45 degree chamfer
- Plastic storage box
- Each bit diameter no more than 1 inch
A 4-piece 1/4 inch shank compact set with flush trim bit 2402, 1/8 inch roundover bit 2000C, template bit 3004 and 45 degree chamfer bit 2292.
Pros
- Made for compact routers and trimmers
- Small diameters fit small base plates
- Four popular bits in one box
Cons
- Only 4 pieces
- Not a full general purpose collection
Whiteside 404 suits owners of compact routers and laminate trimmers.
The four 1/4 inch shank bits are flush trim bit 2402, 1/8 inch roundover bit 2000C, template bit 3004 and 45 degree chamfer bit 2292.
Each bit has a diameter of no more than 1 inch, so they fit small base plates and tight work where a large bit would be awkward.
The 45 degree chamfer bit is made to fit compact routers and pass through the bottom plate without touching the sides, which helps with small edge work.
The set comes in a plastic storage box.
The trade off is clear, since four bits do not build a general purpose collection.
There is no dovetail, cove, V-groove or straight bit here for wider jobs.
For template work, flush trimming, a small roundover and chamfering, this compact set does the core jobs.
If you own a full size router and want broad profiles, the larger sets above give you more range.
How do 1/4 inch and 1/2 inch router bit sets compare?
A 1/4 inch set fits more routers, including compact trim routers, while a 1/2 inch set gives more stability for bigger bits.
Most picks here use 1/4 inch shanks. The BOSCH 10 piece set mixes both shanks, Whiteside 401 uses 1/2 inch only, and Whiteside 404 uses 1/4 inch for compact routers.
Best 1/4 inch shank sets for most routers
If your router takes a 1/4 inch collet, our best 1/4 router bit set guide narrows the field by profile and case style.
Hiltex is the best all round 1/4 inch pick here because its 15 profiles are named and its case is labeled. LU&MN gives you 35 profiles, and MNA 25 gives a middle path with 25 pieces.
KOWOOD and MNA 15 suit beginners and DIY work where a wood case matters more than exact size lists.
Best 1/2 inch shank sets for stability
If your router takes a 1/2 inch collet, our best 1/2 inch shank router bit sets guide focuses on larger shank sets.
Whiteside 401 is the 1/2 inch pick here, with seven exact bits for cove, rabbet, roundover, chamfer, straight and flush trim work.
The BOSCH 10 piece set also gives you some 1/2 inch bits, but it mixes them with 1/4 inch bits. A 1/2 inch shank will not fit a router that only accepts 1/4 inch.
What profiles should a general purpose router bit set include?
A good starter set should include straight bits, a flush trim bit, a roundover, a chamfer, a cove and a V-groove.
Those profiles cover grooving, edge softening, decorative edge work, trimming and simple joinery.
Hiltex covers that core list and adds core box, mortising, dovetail, Roman ogee and panel pilot bits. BOSCH RBS015MBS names its sizes, which helps if you need a 5/8 inch flush trim or a 1/4 x 1/2 inch rabbet.
LU&MN adds beading, wave edge and double Roman ogee profiles for more decorative work.
Straight, flush trim and panel pilot bits
Straight bits cut grooves and slots, flush trim bits copy a pattern or clean an edge, and panel pilot bits cut from the inside of a panel.
Hiltex includes straight bits in 1/8, 1/4, 1/2 and 5/8 inch sizes, plus a 1/4 inch panel pilot and a 1/2 inch flush trim. LU&MN includes six straight bits and four flush trim bits.
MNA sets include straight, panel pilot and bearing flush trim bits, but exact sizes are not listed.
Roundover, chamfer, cove and Roman ogee bits
Roundover and chamfer bits soften edges, cove bits cut concave profiles, and Roman ogee bits shape decorative edges.
Whiteside 401 gives a 3/8 inch radius cove, a 3/8 inch roundover and a 45 degree chamfer in 1/2 inch shank form. Whiteside 404 gives a 1/8 inch roundover and a 45 degree chamfer for compact routers.
Hiltex and BOSCH RBS015MBS both include Roman ogee bits. If edge work is your main job, our best router bits for wood guide helps you match profile to material.
Which router bit set is best for your router brand?
Shank size matters more than brand name, because a 1/4 inch bit fits any router with a 1/4 inch collet.
MNA states its 1/4 inch sets fit Bosch, DeWalt, Makita, Milwaukee, Porter and Cable, Skil, Ryobi and Black and Decker routers.
If you own a DeWalt router, our best router bit set for dewalt guide checks fit by shank and profile. If you own a Ryobi router, our best router bits for ryobi router guide covers Ryobi specific picks and collet checks.
Sets for DeWalt, Bosch, Makita and other major routers
Hiltex says its 1/4 inch shank fits trim, plunge and fixed base routers, which covers most major brands with that collet. MNA names Bosch, DeWalt, Makita, Milwaukee, Porter and Cable, Skil, Ryobi and Black and Decker for its 1/4 inch sets.
BOSCH sets use micrograin carbide and include named profiles. For brand specific checks, use how to change ryobi router bits before you swap bits on a Ryobi router.
Compact routers and laminate trimmers
Compact routers need small diameter bits that fit through a small base plate.
Whiteside 404 is built for that job, with four bits no more than 1 inch in diameter and a chamfer bit made to pass through the plate.
A full 15 or 35 piece set can include bits that are too large for compact work. If your main tool is a trim router, start with a compact set.
How many pieces should you buy in a router bit set?
Buy 15 pieces if you want a first general purpose collection without paying for duplicates.
Most 15 piece sets here cover straight, cove, core box, V-groove, mortising, roundover, dovetail, Roman ogee, chamfer, panel pilot and flush trim work.
Buy 25 or 35 pieces if you run a router table or make varied projects. Buy 4 to 10 pieces if you only need basics or compact work.
15 piece sets for general woodworking
Hiltex, KOWOOD, BOSCH RBS015MBS and MNA 15 all land at 15 pieces. Hiltex and BOSCH name exact profiles, which helps with planning.
KOWOOD and MNA 15 focus on beginner and DIY use with wood cases. That 15 piece count is the sweet spot for most buyers.
If you later need cabinet door profiles, our best router bit sets for cabinet doors guide covers that narrower job.
Larger sets and small basic sets
LU&MN has 35 pieces and MNA has a 25 piece set, which helps if you want duplicates and decorative profiles. Whiteside 401 has 7 pieces and Whiteside 404 has 4 pieces, which helps if you want only core bits.
A small set stores easily but can leave you short for joinery. A large set reduces repeat purchases but needs more care.
What carbide and storage should you look for?
Carbide tips keep an edge longer than plain steel on wood and composites.
Hiltex uses YG8 tungsten carbide, MNA 25 uses C3 carbide, and BOSCH sets use micrograin carbide tips. LU&MN and KOWOOD use tungsten carbide tips for clean cuts.
Storage matters because loose bits dull and get lost. Hiltex uses a labeled hard case, KOWOOD uses a wooden case, BOSCH RBS015MBS uses a plastic case, LU&MN uses an aluminum box, and Whiteside sets use plastic cases.
Carbide types and what they mean
Micrograin carbide tips are ground for sharper edges and smoother finish cuts.
BOSCH states that for its micrograin carbide tips, with anti friction coating to limit residue build up. C3 carbide is an American industry classification that MNA cites for wear resistance.
YG8 tungsten carbide is the grade Hiltex cites for heat resistance and clean cuts in all types of wood. Any of those carbide types will serve you well if the bit is sharp and the feed rate is steady.
Cases, boxes and bench storage
A labeled case helps you find a profile without handling every bit.
Hiltex cases label each slot, which speeds up bit changes. Wooden cases from KOWOOD and MNA 15 protect bits and look tidy on a bench.
The BOSCH 10 piece case has a clear top, so you can see bits at a glance. LU&MN uses an aluminum box, which suits a larger 35 piece set.
Keep bits clean and dry, and use a best router bit bearing set guide if a bearing on a flush trim or roundover bit needs care.
Can a router bit set handle router table work?
Yes, if the shank fits your router and the bit size suits the job.
MNA states its 1/4 inch sets fit benchtop router table use, and BOSCH RBS015MBS is stated for precision cuts and flush trimming on a router table.
Use best router table bits when you need bits made for table use, because taller bits and bearing placement matter more at a table.
Safety, speed and feed for set bits
Match router speed to bit diameter, since larger bits need slower speeds. Keep a steady feed rate to limit burning and tear out.
Do not cut ferrous metal or non wood materials with wood bits, as KOWOOD warns. If you need to cut metal, our best router bit for metal cutting guide covers that different job.
For general wood bits, our best budget router bits guide helps if you want lower cost sets. To choose a profile, use which router bit to use and confirm the profile before you start.
Special profiles like keyhole bits
Most general sets here do not include keyhole bits.
If your project needs a keyhole slot for hanging, our best keyhole router bit set guide covers that special profile.
Buy a general set first, then add special bits for the jobs you actually do.
What is the verdict on the best router bit set?
The best router bit set for most people is the Hiltex Router Bit Set, because its 15 named profiles and labeled case cover general woodworking without extra bulk.
Pick KOWOOD if you want a beginner set in a wooden case. Pick BOSCH RBS015MBS if you want exact named sizes and micrograin carbide.
Pick LU&MN if you want 35 profiles and an aluminum box. Pick MNA 25 if you want a middle count with broad coverage.
Pick BOSCH Router Bits if you need a mix of 1/4 and 1/2 inch shanks. Pick Whiteside 401 for 1/2 inch basics and Whiteside 404 for compact routers.
How we compare router bit sets: specs, profiles and fit
| Product | Best for | Pieces | Shank | Material | Our score |
|---|---|---|---|---|---|
| Hiltex Router Bit Set | most woodworkers | 15 | 1/4 inch | Alloy Steel, Carbide | 9.7 |
| KOWOOD Router Bits Set of 15 Pieces | beginners | 15 | 1/4 inch | Tungsten Carbide | 9.6 |
| BOSCH RBS015MBS 15-Piece Carbide-Tipped Wood Router Bits | named profiles | 15 | Carbide | 9.5 | |
| LU&MN Carbide Tipped Router Bit Set | largest variety | 35 | 1/4 inch | Carbide | 9.3 |
| MNA Router Bit Set 25 Pieces 1/4 | 25 piece value | 25 | 1/4 inch | Carbide | 9.0 |
| BOSCH Router Bits | mixed shank work | 10 | 1/4 inch and 1/2 inch | Blend | 8.8 |
| MNA Router Bits Set 15 Pieces 1/4 | DIY woodworkers | 15 | 1/4 inch | Carbide | 8.6 |
| Whiteside 401 Basic 7 Piece Router Bit | 1/2 inch basics | 7 | 1/2 inch | Carbide | 8.3 |
| Whiteside 404 Compact Router Bit Set | compact routers | 4 | 1/4 inch | High Speed Steel | 8.1 |
We compared router bit sets by shank size, piece count, carbide type, named profiles, case style and stated materials.
We checked fit for handheld, plunge, fixed base, compact and router table use, and which sets name exact bit sizes for planning grooves and flush trims.
That is why Hiltex and BOSCH RBS015MBS score well here, even though LU&MN has more pieces. A larger count does not always beat exact sizes for a first set.
For miter saw work, our Best Miter Saw Blade Carbide Tipped guide covers that separate tool. For Bosch miter saw setup, our How To Release Bosch Miter Saw? guide covers lock and release steps.
Our top 3 picks at a glance
-
1
-
2
-
3
Best for named profilesBOSCH RBS015MBS 15-Piece Carbide-Tipped Wood Router Bits
9.5/10 our score
See it on Amazon
Frequently asked questions
What shank size should I buy?
Buy the shank your router collet accepts. Most sets here use 1/4 inch shanks and fit trim, plunge and fixed base routers with that collet.
If your router accepts 1/2 inch shanks, a 1/2 inch set can give more stability for larger bits.
How many bits do I need to start?
A 15 piece set covers most general woodworking jobs, including straight, flush trim, roundover, chamfer and cove work.
Larger sets add duplicates and extra decorative profiles, which helps if you switch bits often or run a router table.
Can these bits cut MDF and plywood?
Several sets here are stated for wood, MDF, particle board and plywood. KOWOOD and both MNA sets name those materials.
LU&MN also states softwood, hardwood, MDF, particle board, plywood and acrylic composites.
What is the difference between 1/4 and 1/2 inch shank sets?
A 1/2 inch shank is stiffer and vibrates less with larger bits. A 1/4 inch shank fits more compact routers and trim routers.
Check your collet before you order, because the two sizes do not swap without the right collet.
About this guide: Our look at router bit sets draws on maker specs, materials and what owners report. See how we research.



