How to Choose a Router Table for a Craftsman Router
A router table for Craftsman router use works when its mounting plate matches your base pattern and leaves the switch and height lock reachable. Check hole spacing, plate opening, fence alignment and dust ports before you buy. Then confirm the table height, weight and work area fit your shop space.
On this page (11 sections)
- How do I check mounting patterns and adjustment access for Craftsman router installations?
- Is a benchtop or cabinet style better for a Craftsman router table?
- What table size and work area do I need?
- How does a fence help with straight and curved work?
- What dust collection features should a router table have?
- How do featherboards, guards and accessory slots improve safety?
- What router should I pair with a router table?
- How do I set up a router table for Craftsman router use step by step?
- What care and checks keep a router table accurate?
- How do I compare the Bosch RA1181 and RA1171 for this use?
- What should I check before I buy a router table for Craftsman router use?
A router table for Craftsman router use needs a plate, fence and controls that match your exact base and work style.
The right table holds the router rigid, keeps the switch clear and lets you set height without removing the motor.
We checked the specs and features of the tables and router below to show what to measure. Start with your router, not the table.
Remove the base if you can, trace the screw holes and note the motor shape. A strong and flat table can still fail if the plate opening clips the base or covers the lock.
How do I check mounting patterns and adjustment access for Craftsman router installations?
Mounting fit decides if a router table for Craftsman router use is safe and easy to set up.
Check base diameter, screw spacing, plate opening and switch clearance before you check fence or dust features.
A plate that matches one Craftsman model may not match another with a different base shell. Take the fixed base off the motor and lay it upside down on paper.
Mark each screw hole, then measure center to center in two directions. Note any raised ribs or a wide skirt that could hit the plate edge.
Check where the on and off switch sits once the base is mounted. The table top should not cover the switch or trap your hand during start up.
Height locks and depth rods also need room so you can reach them from below or above the table.

A 27 in. by 18 in. aluminum top with a rigid plate predrilled for a variety of routers and above table height adjustment.
See it on AmazonThe Bosch RA1181 uses a rigid aluminum mounting plate predrilled for a variety of routers. That helps with above table height adjustment on many common routers, but you still need to match your own hole pattern.
For compatible full-size setups, compare router lifts for full-size routers.
Bring your base measurements to the plate diagram, or ask the seller for that diagram before you order. If you must remove the router for every small height change, work slows and test cuts get skipped.
Firm rule: buy only when the plate holes, opening and switch clearance match your Craftsman base on your own measurements, never on brand name alone.
How do I measure a Craftsman base for a router table?
Measure the fixed base as you will mount it, since that is the base used for most table work.
Record length, width, hole spacing and offset from the bit center. Trace the outline on a flat sheet and mark the bit center on it.
The plate opening must clear the bit and collet parts and leave room for the motor body to move. If your bit shank and router collet sizes differ, see 1/2-inch to 8mm router collet adapters.
Check the motor body above the base too, as a tall motor can hit a fence, guard or dust box. Note the sub base and any dust adapter, since a wide sub base may need a larger opening.
Trace the base, measure the holes and test switch access first, then compare that trace with the plate diagram.
Is a benchtop or cabinet style better for a Craftsman router table?
The style you pick depends on how often you use the table and how much floor space you have.
A benchtop table suits occasional work and small shops, while a cabinet table suits steady work and better dust control.
Neither style makes a poor mounting fit work. A benchtop table keeps a small footprint and moves to storage when you finish.
That helps if you share a garage or store tools on shelves. The trade off is less room for dust boxes, storage and a fixed outfeed surface.
A cabinet table acts like a small stand with enclosed space below the top. That enclosure can hold a dust collection setup and keep accessories in one place.
It also adds weight and floor space, so measure the spot before you commit.

A cabinet style table with a smooth laminated top, tall fence and two dust ports for steady shop use.
See it on AmazonThe Bosch RA1171 has a cabinet style design with a smooth laminated top. Bosch describes that design as ideal for stability, storage and dust management.
Its base has four predrilled holes for screws, and a flat extension allows clamping to a workbench. The RA1181 weighs 30 pounds and measures 18 in. wide by 14.5 in. high.
The RA1171 weighs 35 pounds and measures 24.2 in. wide by 4.8 in. high. Weight and footprint should be checked against your bench and storage plan.
Firm rule: choose benchtop for space saving occasional use, and choose cabinet style for frequent use where storage and dust control matter.
Which style suits small shops and frequent users?
Small shops often need a table that moves. A benchtop model can sit on a bench for a run, then move aside for other work.
The aluminum top on the RA1181 gives a 27 in. by 18 in. work area in a portable frame. Frequent users need a table that stays set up.
A cabinet style gives a fixed height and a place for dust runs and featherboards. That steady setup helps when you repeat the same profile on a set of parts.
Think about your main stock size. Long boards need support on both sides of the fence.
Short trim pieces need a fence and featherboards that keep hands clear. Cabinet tables often give more room for those supports below the top.
Firm rule: match the style to your use rate and floor space first, then match the mounting plate to your router.
What table size and work area do I need?
Table size should match your longest and widest work.
Pick a top large enough to support stock on both sides of the bit without rocking or tipping.
Measure the stock you route most often, such as door trim, cabinet frames and drawer fronts. Wide panels need flat support as they move past the bit.
Height and balance matter too, as a wobbling table will shift the cut. The RA1181 gives a large aluminum top measuring 27 in. by 18 in., while the RA1171 has a smooth laminated top in a cabinet style frame.
How does a fence help with straight and curved work?
A fence guides straight work and keeps stock square to the bit.
Choose a tall fence with adjustable faceplates so you can run tall stock and split the fence for wide bits.
Straight edge work needs a fence face that sits flat against the stock. Adjustable faceplates let you open a gap for the bit and set one side for an outfeed shim.
Curved work needs a different setup. A starter pin or guard can support stock that does not sit against a flat fence, and both the RA1171 and RA1181 include that starter pin and guard.
Featherboards add control by pressing work toward the fence and down to the table. Both Bosch tables list adjustable featherboards that attach to fence and table to provide guidance and kickback protection.

A 14 amp router with fixed and plunge bases, soft start and a speed control LCD display for choosing bit settings.
See it on AmazonThe Skil RT1322-00 in the set above is a router, not a table, but its features show why fence control matters. It has a 14 amp motor, soft start and electronic feedback.
Those controls help the motor hold speed, yet the fence still decides if the cut stays straight.
Firm rule: buy a tall fence with adjustable faces and featherboard slots, then test square with a long offcut before you cut good stock.
How do I set the fence for straight, curved and tall work?
Start with straight work. Set the fence faces so the bit just clears the face, then check both faces with a straight edge.
Move one face back for a second pass if you need a deeper cut. For tall stock, use the full height of the fence.
Tall fences help keep tall boards from tipping toward the bit. The RA1181 and RA1171 both list an extra tall aluminum fence.
For curved work, remove the fence from the path and use a pin or guard as the pivot point. Move the stock slowly against the pin so the bit follows the curve you want.
For outfeed work, add shims behind the outfeed face so the cut side has support. Both Bosch tables include outfeed shims.
Set the fence for the work in front of you, and change the setup when the stock shape changes.
What dust collection features should a router table have?
Dust collection keeps the bit visible and the cut clean.
Look for a standard hose port, a port near the fence and a seal around the plate opening.
A port at the fence catches chips where the bit meets the wood, and a port below the top catches dust that falls through the plate opening. Placement matters as much as port size with fine dust at high speed.
The RA1181 has a dedicated port that fits 2-1/2 in. vacuum hoses. The RA1171 has two dedicated ports, one at the fence and one at the cabinet, and both tables accept 3/4 in. optional accessories such as a miter gauge.
How do featherboards, guards and accessory slots improve safety?
Safety parts keep work pressed to the fence and hands away from the bit.
Use featherboards to guide stock, keep guards in place and keep your hands clear of the bit path.
Featherboards press work toward the fence and down to the table. Both the RA1181 and RA1171 list adjustable featherboards that attach to fence and table for guidance and kickback protection.
The RA1171 includes an adjustable clear guard so you can see the cut while keeping chips and hands away. Both tables accept 3/4 in. optional accessories such as a miter gauge, but that should not replace a fence for long edge work.
What router should I pair with a router table?
A router for table use needs enough power, speed control and base options for the bit and stock you plan to cut.
Pick a router with fixed base use, speed settings and both collet sizes you need for your bits.
The Skil RT1322-00 is a 14 amp router with fixed and plunge bases. Skil describes it as 14 amp, 2.5 hp in one bullet and 2.42 hp in the specs.
Speed control matters more in a table because the bit is fixed and work moves past it. It has a speed control LCD display to select bit type and material for suggested settings, plus electronic feedback to help hold rpm.
Soft start gives a safe and controlled start with a large bit. Included parts include 1/4 in. and 1/2 in. collets, a collet wrench, fixed and plunge base dust extraction adapters, an edge guide and a parallel guide.
How do I set up a router table for Craftsman router use step by step?
Setup should be slow and in order.
Mount the router, check plate level, set the fence, add featherboards, connect dust and make a test cut before you route good stock.
Start by mounting the router to the plate with the correct screws and holes. Tighten in a cross pattern so the base sits flat.
Check for rocking by pressing each corner. Next, confirm the plate sits flush with the table top.
A plate that sits high or low will catch stock at the opening. The Bosch plates are described as rigid aluminum.
Then set the fence. Square the fence to the top, open the faceplates for the bit and add outfeed shims if you need them.
Add featherboards after the fence is set, not before. Connect the dust hose and turn on collection before you start the router.

A benchtop table with a tall aluminum fence, adjustable faceplates and a 2-1/2 in. dust port for clean cuts.
See it on AmazonMake a test cut on scrap that matches your final stock. Check for burn marks, tear out and fence drift.
Adjust bit height in small steps and lock the height after each change. Above table adjustment helps here if your router and plate allow it.
Firm rule: mount, level, fence, featherboard, dust, then test on scrap, in that order every time.
How do I check height, lock and switch access after mounting?
Height access decides if you will actually make small changes. A router that is hard to adjust invites you to accept a cut that is off.
Check the height lock from the position you will stand. You should be able to reach the lock, move the motor and lock it again without lifting the router out.
Check the switch at the same time. The switch should stay clear of the plate and the fence.
A switch hidden under the top slows your response. Also check the cord path.
A cord that hangs across the work area can pull on the motor or catch on stock. Route the cord away from the bit and keep it clear of the fence line.
Firm rule: if you cannot reach the lock and switch from your working position, fix the setup before you route.
What care and checks keep a router table accurate?
Care keeps a router table flat, square and safe.
Wipe the top, check the plate, square the fence and clear dust ports after each use.
Wipe aluminum tops to remove pitch and fine dust, since a thin film can make stock drag or shift. Check the mounting plate for loose screws and bent edges, because a loose screw can let the router shift and change bit height.
Check fence square after moves or drops with a square against the top and fence face. Clear dust ports and slots often, since packed dust can block airflow and make featherboards hard to seat.
The RA1181 has a storage pocket and cord wrap storage for 6 ft. of power cord.
How do I compare the Bosch RA1181 and RA1171 for this use?
The two Bosch tables solve the same mounting problem in different ways.
Pick the RA1181 for portable benchtop use and the RA1171 for fixed cabinet use with more dust points.
Both use rigid aluminum plates predrilled for a variety of routers. The RA1181 has a 27 in. by 18 in. aluminum top, an extra tall aluminum fence with adjustable faceplates and featherboards, a 2-1/2 in. vacuum hose port, a storage pocket, and weighs 30 pounds.
The RA1171 has a smooth laminated top, an extra tall aluminum fence with adjustable MDF faceplates and featherboards, two dust ports, one at the fence and one at the cabinet, and weighs 35 pounds. Both accept featherboards and 3/4 in. optional accessories such as a miter gauge and list above table height adjustment with many common routers.
If you want to compare a related brand fit, read our guide to a router table for bosch router. If you want a broader view of table types, see our best router table for woodworking roundup, and for a general parts overview, our router table attachment guide explains how plates, fences and dust parts work together.
What should I check before I buy a router table for Craftsman router use?
Buy only after you check fit, size, fence, dust and access.
Measure your base, measure your space and confirm the plate diagram before you pay.
Measure your base and trace the holes, then measure the floor or bench space where the table will live. A benchtop table needs bench room and storage space, while a cabinet table needs floor space and room to reach ports.
Check fence height and faceplate setup against your tallest stock, and check featherboard and accessory slots so you can add control parts later. Check dust ports against your shop vac or dust collector, since a 2-1/2 in. port fits standard hoses but you should confirm your hose size and adapter needs.
For more on router types that pair with these tables, start with our guide to wood routers for woodworking. If you also use Craftsman saws in the shop, our How To Use Craftsman Miter Saw? guide and How To Set Craftsman Miter Saw? guide cover setup checks for that tool, and for a different brand fit, compare our router table for dewalt router guide.
Frequently asked questions
What do I check first for a Craftsman router table?
Check base diameter, screw hole pattern, motor body shape and switch position first. Those four points decide if the plate holds the router firm and leaves controls clear.
Take the fixed base to the shop or measure it with calipers before ordering a table or insert plate.
Can one table fit several router brands?
Many tables use predrilled plates for a range of common routers, but predrilled does not mean universal. The Bosch RA1181 and RA1171 both describe rigid aluminum plates predrilled for a variety of routers.
Count the holes on your base and compare that layout with the plate diagram before you assume a fit.
Is a benchtop or cabinet table better for a Craftsman router?
A benchtop table suits small shops and short runs where you store the table between uses. A cabinet table suits frequent use and gives room for storage and dust collection.
Your work rate, floor space and dust setup should decide, not the router brand alone.
Why does above table height setting matter?
Above table adjustment lets you change bit height from the top without removing the router. That saves time for test cuts and small changes.
It only helps if your router base, lift parts and plate opening allow the motor to move and lock at the new height.
What fence features matter most?
Look for a tall fence, adjustable faceplates, featherboard slots and a dust port near the bit. Those parts help with tall stock, split fence setups and chip control.
A fence that stays square to the top matters as much as its height on long edge work.
About this guide: Our look at router table for Craftsman router draws on maker specs, materials and what owners report. See how we research.



